कंडक्टर डरेटिंग और वोल्टेज ड्रॉप: दोनों जांच पास करने वाला वायर साइज
Breaker के हिसाब से wire size सही दिख सकता है, फिर भी design गलत हो सकता है। Derating heat check है; voltage drop load end पर usable voltage check करता है।
NEC में 310.16, 310.15(B), 310.15(C)(1), 110.14(C), 210.19(A)(1) और 215.2(A)(1) देखें। IEC काम में IEC 60364-5-52 मुख्य reference है। NEC IEC
Derating और voltage drop अलग जांच क्यों हैं
Derating thermal safety check है: ज्यादा loaded conductors और temperature usable ampacity घटाते हैं।
Voltage drop performance check है: लंबाई, current, low voltage और motor starting load voltage घटाते हैं।
Derating के कारण wire बड़ा करना मदद करता है, पर हमेशा voltage drop के लिए काफी नहीं होता।
Terminal temperature जरूरी है; NEC 110.14(C) final result को 60C या 75C तक सीमित कर सकता है।
Worksheet पर लिखने योग्य code references
- NEC 310.16: material, insulation और terminal के सही ampacity table से शुरू करें।
- NEC 310.15(B) और 310.15(C)(1): ambient temperature और loaded conductor count लागू करें।
- NEC 210.19(A)(1) और 215.2(A)(1): common target branch 3% और total 5% है।
- IEC 60364-5-52: installation method, grouping, ambient correction और voltage-drop limit तय करता है।
जहाँ एक जांच काफी नहीं होती
ये planning values हैं। Calculator में derating के बाद final size डालें, breaker से match होने वाला पहला minimum size नहीं।
| Circuit | Derating condition | Thermal result | Voltage-drop result |
|---|---|---|---|
| 20A branch circuit, 150 ft / 46 m | 9 current-carrying conductors, 40C | 10 AWG Cu passes ampacity after derating | 8 AWG Cu keeps 120V drop near 3.8% instead of 6.0% |
| 60A, 208V three-phase feeder, 220 ft / 67 m | 6 current-carrying conductors, 50C | 4 AWG Cu remains thermally legal | 2 AWG Cu cuts drop from about 3.4% to 2.1% |
| 32A, 400V IEC circuit, 50 m | 10 loaded conductors on tray, 45C | 10 mm2 Cu clears grouping and ambient factors | 10 mm2 stays near 1.2% voltage drop |
| 120V workshop receptacles, 100 ft / 30 m | 12 conductors in one raceway | 12 AWG can fail the adjustment check | 8 AWG may be needed when both heat and drop matter |
Specific numbers वाले examples
20A receptacle run, 150 ft, 120V, 9 loaded conductors
40C पर THHN copper और 9 loaded conductors में 70% और लगभग 0.91 correction से 12 AWG tight हो जाता है। 10 AWG ampacity पास कर सकता है, पर drop लगभग 7.2V यानी 6.0% है। 8 AWG इसे 4.6V यानी 3.8% करता है।
60A, 208V three-phase feeder, 220 ft
6 loaded conductors में 80% adjustment चाहिए। 50C पर 4 AWG copper THHN 60A के लिए thermally legal हो सकता है, लेकिन drop लगभग 7.0V या 3.4% है। 2 AWG इसे 4.4V या 2.1% करता है।
32A, 400V IEC circuit, 50 m tray
10 loaded conductors और 45C में 6 mm2 copper corrected current में fail हो सकता है। 10 mm2 thermal check पास करता है और three-phase drop करीब 4.9V, यानी 1.2% रखता है।
Result पर भरोसा करने से पहले checklist
- Load current, continuous load, material, insulation और terminal limit से शुरू करें।
- Voltage drop से पहले ambient और conductor count correction लगाएँ।
- One-way length डालें और सही single-phase, three-phase, AC या DC method चुनें।
- Panel पहले से दूर हो तो feeder plus branch total drop जांचें।
- Result 3% या 5% के पास हो तो एक size बड़ा चुनें।
Calculator में derated final size इस्तेमाल करें
पहले conductor को thermally legal बनाएं। फिर size, current, voltage, material, phase और distance डालें।
Start Calculating
Ready to apply these concepts to your project? Use our professional voltage drop calculator.
Open Calculator