연속 부하 전압 강하: 125% 전류, 전선 굵기, NEC/IEC 설계
EVSE, 조명, 히터 회로를 NEC 210.20, NEC 215.3, NEC 625, IEC 60364와 125% 연속 부하 기준으로 검토합니다.
연속 부하는 전류가 몇 시간 동안 유지됩니다. 48 A EV 충전기, 18 A 조명 회로, 36 A 히터는 차단기 정격만으로 충분하지 않으며 전압 강하와 열 조건을 함께 봐야 합니다.
요약
- 3 hours or more makes the load continuous in NEC practice.
- 125% sizing and voltage-drop calculation answer different questions.
- Use branch, feeder, and total voltage-drop budgets together.
- EVSE, lighting, heaters, and ventilation loads need sustained-current checks.
연속 부하는 최대 전류가 3시간 이상 지속될 것으로 예상되는 부하입니다. 전압 강하는 도체 임피던스로 인해 부하단 전압이 낮아지는 현상입니다. 허용 전류는 정해진 조건에서 도체가 온도 정격을 넘지 않고 흘릴 수 있는 전류입니다.
NEC 210.20(A), 215.3, 625로 125% 회로 기준을 정한 뒤 실제 지속 전류, 편도 길이, 도체 재질, 피더 여유를 사용해 전압 강하를 계산합니다. NEC and IEC references keep the thermal and performance checks separate.
The 125% continuous-load rule is a heat and protection rule; it does not erase the resistance of a 150-foot branch circuit.
— Hommer Zhao, Technical Director
Continuous-load design checks
48 A, 240 V EVSE는 보통 60 A 회로입니다. 6 AWG 구리, 편도 165 ft에서는 분기 회로 강하가 약 6.3 V, 2.6%이고 피더 1.8%를 더하면 약 4.4%입니다.
| Load | Sustained current | NEC basis | Route | Design action |
|---|---|---|---|---|
| Level 2 EVSE | 32 A at 240 V | 40 A circuit | 130 ft | Compare 6 AWG Cu |
| High-output EVSE | 48 A at 240 V | 60 A circuit | 165 ft | Check feeder plus branch |
| LED lighting row | 18 A at 277 V | 125% review | 240 ft | Split row or upsize |
| Process heater | 36 A at 208 V | 45 A design current | 110 ft | Check 6 AWG and source |
| Exterior lighting | 12 A at 120 V | 15 A basis | 95 ft | Use 10 AWG or split |
For a 48-amp EV charger, document the 60-amp circuit sizing and check voltage drop at the sustained charging current.
— Hommer Zhao, Technical Director
Practical warning
125% 규칙은 지속 발열과 보호를 위한 것이지 긴 전선의 저항을 없애는 규칙이 아닙니다.
Use the wire size calculator, the NEC requirements article, and the voltage drop vs ampacity guide together before material is released.
Continuous loads turn small voltage-drop misses into daily operating losses because the circuit stays loaded for hours.
— Hommer Zhao, Technical Director
FAQ
전압 강하는 100% 또는 125% 중 무엇으로 계산하나요?
부하단 성능은 실제 지속 전류로 확인하고, NEC 회로 선정은 필요한 경우 125%를 적용합니다.
EVSE는 연속 부하인가요?
예. NEC 625에서 EVSE는 연속 부하로 취급되며 48 A 장비는 일반적으로 60 A 회로가 필요합니다.
조명 회로 목표값은?
분기 3%, 피더 포함 총 5%가 일반적이며 긴 LED 회로는 2-3%가 더 좋습니다.
언제 전선을 키워야 하나요?
거리가 길거나 피더가 이미 약 2%를 사용했거나 부하가 3시간 이상 지속될 때입니다.
IEC 기준은 어떻게 보나요?
IEC 60364-5-52는 설계 전류, 시공 방식, 주변 온도, 그룹화, 허용 전압 강하를 함께 봅니다.
전선을 발주하기 전에 최소 굵기와 한 단계 큰 굵기를 계산기로 비교하세요.
Start Calculating
Ready to apply these concepts to your project? Use our professional voltage drop calculator.
Open Calculator