Susut voltan beban berterusan: 125%, saiz kabel dan NEC/IEC
Saizkan EVSE, lampu dan pemanas sebagai beban berterusan.
Beban berterusan mengekalkan arus selama berjam-jam. EVSE 48 A, litar lampu 18 A atau pemanas 36 A perlu disemak dari segi haba dan susut voltan sebenar.
Ringkasan
- 3 hours or more makes the load continuous in NEC practice.
- 125% sizing and voltage-drop calculation answer different questions.
- Use branch, feeder, and total voltage-drop budgets together.
- EVSE, lighting, heaters, and ventilation loads need sustained-current checks.
Beban berterusan ialah beban yang boleh berjalan pada arus maksimum selama 3 jam atau lebih. Susut voltan ialah kehilangan voltan pada impedans konduktor. Ampacity ialah arus dibenarkan tanpa melebihi suhu konduktor.
Gunakan 125% dahulu mengikut NEC 210.20(A), 215.3 atau 625 jika berkenaan, kemudian kira susut voltan dengan arus berterusan, panjang laluan, bahan konduktor dan bajet feeder. NEC and IEC references keep the thermal and performance checks separate.
The 125% continuous-load rule is a heat and protection rule; it does not erase the resistance of a 150-foot branch circuit.
— Hommer Zhao, Technical Director
Continuous-load design checks
EVSE 48 A pada 240 V biasanya menggunakan litar 60 A. Dengan tembaga 6 AWG dan 165 ft sehala, susut cabang sekitar 2.6%; bersama feeder 1.8%, jumlahnya hampir 4.4%.
| Load | Sustained current | NEC basis | Route | Design action |
|---|---|---|---|---|
| Level 2 EVSE | 32 A at 240 V | 40 A circuit | 130 ft | Compare 6 AWG Cu |
| High-output EVSE | 48 A at 240 V | 60 A circuit | 165 ft | Check feeder plus branch |
| LED lighting row | 18 A at 277 V | 125% review | 240 ft | Split row or upsize |
| Process heater | 36 A at 208 V | 45 A design current | 110 ft | Check 6 AWG and source |
| Exterior lighting | 12 A at 120 V | 15 A basis | 95 ft | Use 10 AWG or split |
For a 48-amp EV charger, document the 60-amp circuit sizing and check voltage drop at the sustained charging current.
— Hommer Zhao, Technical Director
Practical warning
Peraturan 125% mengurus haba dan perlindungan, bukan rintangan kabel panjang.
Use the wire size calculator, the NEC requirements article, and the voltage drop vs ampacity guide together before material is released.
Continuous loads turn small voltage-drop misses into daily operating losses because the circuit stays loaded for hours.
— Hommer Zhao, Technical Director
FAQ
¿Calculo al 100% o al 125%?
Use la corriente sostenida real para caída de tensión y el 125% para dimensionamiento cuando NEC lo exige.
¿Un cargador EV es carga continua?
Sí. NEC 625 trata el EVSE como carga continua; 32 A suele requerir 40 A y 48 A suele requerir 60 A.
¿Qué objetivo uso en iluminación?
3% en rama y 5% total son objetivos comunes; líneas LED largas van mejor cerca de 2-3%.
¿Cuándo subo calibre?
Cuando la ruta es larga, el alimentador ya usa cerca de 2% o el equipo trabaja más de 3 horas.
¿Cómo se compara IEC?
IEC 60364-5-52 coordina corriente de diseño, método de instalación, agrupamiento, temperatura y caída permitida.
Bandingkan saiz minimum dengan saiz seterusnya sebelum menarik kabel.
Start Calculating
Ready to apply these concepts to your project? Use our professional voltage drop calculator.
Open Calculator