Spanningsval bij continue belasting: 125%, draaddikte en NEC/IEC
Ontwerp EVSE, verlichting en verwarming als continue belasting met NEC en IEC.
Een continue belasting houdt urenlang stroom vast. Een EVSE van 48 A, een lichtlijn van 18 A of een verwarming van 36 A vraagt daarom zowel thermische controle als echte spanningsvalberekening.
Kort
- 3 hours or more makes the load continuous in NEC practice.
- 125% sizing and voltage-drop calculation answer different questions.
- Use branch, feeder, and total voltage-drop budgets together.
- EVSE, lighting, heaters, and ventilation loads need sustained-current checks.
Een continue belasting is een belasting die 3 uur of langer op maximale stroom kan werken. Spanningsval is het spanningsverlies in de geleiderimpedantie. Ampaciteit is de toegestane stroom zonder de temperatuurgrens te overschrijden.
Pas eerst 125% toe waar NEC 210.20(A), 215.3 of 625 dat vragen. Reken daarna met werkelijke continue stroom, lengte, materiaal en resterend feederbudget. NEC and IEC references keep the thermal and performance checks separate.
The 125% continuous-load rule is a heat and protection rule; it does not erase the resistance of a 150-foot branch circuit.
— Hommer Zhao, Technical Director
Continuous-load design checks
Een EVSE van 48 A op 240 V gebruikt vaak een circuit van 60 A. Met 6 AWG koper en 165 ft enkele lengte is de takval ongeveer 2,6%; met 1,8% feederverlies komt totaal rond 4,4%.
| Load | Sustained current | NEC basis | Route | Design action |
|---|---|---|---|---|
| Level 2 EVSE | 32 A at 240 V | 40 A circuit | 130 ft | Compare 6 AWG Cu |
| High-output EVSE | 48 A at 240 V | 60 A circuit | 165 ft | Check feeder plus branch |
| LED lighting row | 18 A at 277 V | 125% review | 240 ft | Split row or upsize |
| Process heater | 36 A at 208 V | 45 A design current | 110 ft | Check 6 AWG and source |
| Exterior lighting | 12 A at 120 V | 15 A basis | 95 ft | Use 10 AWG or split |
For a 48-amp EV charger, document the 60-amp circuit sizing and check voltage drop at the sustained charging current.
— Hommer Zhao, Technical Director
Practical warning
De 125%-regel gaat over warmte en beveiliging, niet over het verdwijnen van weerstand in lange kabels.
Use the wire size calculator, the NEC requirements article, and the voltage drop vs ampacity guide together before material is released.
Continuous loads turn small voltage-drop misses into daily operating losses because the circuit stays loaded for hours.
— Hommer Zhao, Technical Director
FAQ
¿Calculo al 100% o al 125%?
Use la corriente sostenida real para caída de tensión y el 125% para dimensionamiento cuando NEC lo exige.
¿Un cargador EV es carga continua?
Sí. NEC 625 trata el EVSE como carga continua; 32 A suele requerir 40 A y 48 A suele requerir 60 A.
¿Qué objetivo uso en iluminación?
3% en rama y 5% total son objetivos comunes; líneas LED largas van mejor cerca de 2-3%.
¿Cuándo subo calibre?
Cuando la ruta es larga, el alimentador ya usa cerca de 2% o el equipo trabaja más de 3 horas.
¿Cómo se compara IEC?
IEC 60364-5-52 coordina corriente de diseño, método de instalación, agrupamiento, temperatura y caída permitida.
Vergelijk de minimale draad met de volgende maat voordat u trekt.
Start Calculating
Ready to apply these concepts to your project? Use our professional voltage drop calculator.
Open Calculator