Spadek napięcia przy obciążeniu ciągłym: 125%, przewód i NEC/IEC
Dobór EVSE, oświetlenia i grzałek jako obciążeń ciągłych według NEC i IEC.
Obciążenie ciągłe utrzymuje prąd przez wiele godzin. Ładowarka EV 48 A, ciąg oświetlenia 18 A albo grzałka 36 A wymagają osobno sprawdzenia cieplnego i spadku napięcia na rzeczywistej trasie.
W skrócie
- 3 hours or more makes the load continuous in NEC practice.
- 125% sizing and voltage-drop calculation answer different questions.
- Use branch, feeder, and total voltage-drop budgets together.
- EVSE, lighting, heaters, and ventilation loads need sustained-current checks.
Obciążenie ciągłe to obciążenie pracujące z maksymalnym prądem przez 3 godziny lub dłużej. Spadek napięcia to utrata napięcia na impedancji przewodu. Obciążalność to prąd dopuszczalny bez przekroczenia temperatury przewodu.
Najpierw zastosuj 125% tam, gdzie wymaga tego NEC 210.20(A), 215.3 lub 625, a potem policz spadek dla rzeczywistego prądu, długości, materiału przewodu i zapasu zasilacza. NEC and IEC references keep the thermal and performance checks separate.
The 125% continuous-load rule is a heat and protection rule; it does not erase the resistance of a 150-foot branch circuit.
— Hommer Zhao, Technical Director
Continuous-load design checks
EVSE 48 A przy 240 V zwykle oznacza obwód 60 A. Dla 6 AWG Cu i 165 ft w jedną stronę spadek gałęzi wynosi około 2,6%; z zasilaczem 1,8% całość zbliża się do 4,4%.
| Load | Sustained current | NEC basis | Route | Design action |
|---|---|---|---|---|
| Level 2 EVSE | 32 A at 240 V | 40 A circuit | 130 ft | Compare 6 AWG Cu |
| High-output EVSE | 48 A at 240 V | 60 A circuit | 165 ft | Check feeder plus branch |
| LED lighting row | 18 A at 277 V | 125% review | 240 ft | Split row or upsize |
| Process heater | 36 A at 208 V | 45 A design current | 110 ft | Check 6 AWG and source |
| Exterior lighting | 12 A at 120 V | 15 A basis | 95 ft | Use 10 AWG or split |
For a 48-amp EV charger, document the 60-amp circuit sizing and check voltage drop at the sustained charging current.
— Hommer Zhao, Technical Director
Practical warning
Reguła 125% dotyczy ciepła i zabezpieczenia. Nie usuwa rezystancji długiego przewodu.
Use the wire size calculator, the NEC requirements article, and the voltage drop vs ampacity guide together before material is released.
Continuous loads turn small voltage-drop misses into daily operating losses because the circuit stays loaded for hours.
— Hommer Zhao, Technical Director
FAQ
¿Calculo al 100% o al 125%?
Use la corriente sostenida real para caída de tensión y el 125% para dimensionamiento cuando NEC lo exige.
¿Un cargador EV es carga continua?
Sí. NEC 625 trata el EVSE como carga continua; 32 A suele requerir 40 A y 48 A suele requerir 60 A.
¿Qué objetivo uso en iluminación?
3% en rama y 5% total son objetivos comunes; líneas LED largas van mejor cerca de 2-3%.
¿Cuándo subo calibre?
Cuando la ruta es larga, el alimentador ya usa cerca de 2% o el equipo trabaja más de 3 horas.
¿Cómo se compara IEC?
IEC 60364-5-52 coordina corriente de diseño, método de instalación, agrupamiento, temperatura y caída permitida.
Przed ułożeniem przewodu porównaj minimalny przekrój z kolejnym rozmiarem.
Start Calculating
Ready to apply these concepts to your project? Use our professional voltage drop calculator.
Open Calculator