How much voltage drop is acceptable on a 24 V DC control circuit?

A 5 percent limit is often a practical maximum for 24 V DC control wiring because it leaves about 22.8 V at the load. Many PLC inputs and sensors tolerate 20.4 V to 28.8 V, but solenoids and relays should be checked against their pickup voltage.

Do I calculate 24 V DC voltage drop with one-way or round-trip length?

Use the round-trip conductor path for two-wire DC circuits. If the device is 180 ft from the power supply, the current travels about 360 ft through the positive and 0 V conductors, even though the physical route is 180 ft one way.

Does NEC Article 725 replace voltage-drop calculation for Class 2 wiring?

No. NEC Article 725 covers Class 1, Class 2, and Class 3 circuit installation requirements, but it does not guarantee delivered voltage. A Class 2 24 V circuit still needs conductor resistance checked when the load is far from the supply.

What wire size should I use for a 24 V DC solenoid 150 ft away?

For a 0.7 A solenoid at 150 ft one way, 18 AWG copper can drop about 1.9 V, or 7.9 percent. Moving to 16 AWG reduces the drop to about 1.2 V, or 5.0 percent, and 14 AWG gives more margin.

Why do PLC inputs work while solenoids fail on the same 24 V supply?

PLC inputs may draw only 3 mA to 10 mA, so voltage drop is tiny. A solenoid or relay coil may draw 0.3 A to 1.0 A, making the same 200 ft route a real voltage-drop problem.

When is a local 24 V power supply better than larger control cable?

A local power supply often wins when several loads share a route longer than 200 ft or total current exceeds about 2 A. Feed the local supply with an AC branch circuit, then keep the 24 V DC device wiring short.

Cadere de tensiune 24 V DC in circuite de control: PLC, senzori, relee si solenoizi

Un circuit de control 24 V DC alimenteaza intrari PLC, senzori, bobine de releu si solenoizi. O pierdere de 2 V inseamna 8,3% si poate provoca functionare instabila.

Pe scurt

24 V DC: 2 V = 8.3% voltage loss.
La DC cu doua fire se calculeaza dus-intors. Un dispozitiv la 150 ft inseamna circa 300 ft de conductor electric.
Use 3% to 5% as a practical design target.
Check NEC 725, IEC 60204-1, and IEC 61131-2 beside the math.

Cadere de tensiune 24 V DC in circuite de control: PLC, senzori, relee si solenoizi

La DC cu doua fire se calculeaza dus-intors. Un dispozitiv la 150 ft inseamna circa 300 ft de conductor electric.

Un solenoid de 0,7 A la 150 ft pe cupru 18 AWG pierde aproximativ 1,34 V; la sarcina raman circa 22,66 V.

NEC 725 acopera Class 1/2/3; IEC 60204-1 si IEC 61131-2 se aplica masinilor si PLC I/O.

NEC and IEC references define the installation context; delivered voltage is still a circuit-performance calculation.

24 V DC load comparison

Device	Current	150 ft, 18 AWG	Decision
PLC input	3-10 mA	<0.02 V	Noise and threshold matter most
Sensor	20-60 mA	0.04-0.12 V	Check output loading
Relay coil	80-200 mA	0.15-0.38 V	Check pickup voltage
Solenoid	300-700 mA	0.57-1.34 V	Often controls wire size
Valve group	1-3 A	1.9-5.7 V	Consider larger feed or local supply

Practical checks

Calculate the worst simultaneous current, include shared 0 V conductors, compare 18 AWG, 16 AWG, and 14 AWG, then decide whether a local 24 V supply is cleaner than a larger cable. A 24 V circuit should be checked at the device terminals, not only at the power supply.

Documentati tensiunea, distanta, sectiunea, curentul simultan si tensiunea minima la sarcina.

DC Calculator Wire Resistance Contact

Cadere de tensiune 24 V DC in circuite de control: PLC, senzori, relee si solenoizi

Pe scurt

Cadere de tensiune 24 V DC in circuite de control: PLC, senzori, relee si solenoizi

24 V DC load comparison

Practical checks

Start Calculating

Related Articles

Cadere de tensiune vs ampacitate: cand conductorul trebuie marit

Conduit Fill and Derating: Voltage Drop Planning for Crowded Raceways

Long Branch Circuit Voltage Drop: Wire Size, Distance, and NEC/IEC Limits