Spänningsfall vid kontinuerlig last: 125 %, ledararea och NEC/IEC
Dimensionera EVSE, belysning och värmare som kontinuerliga laster.
En kontinuerlig last håller strömmen i flera timmar. En EVSE på 48 A, en belysningsrad på 18 A eller en värmare på 36 A kräver både termisk kontroll och verkligt spänningsfall.
Kort sagt
- 3 hours or more makes the load continuous in NEC practice.
- 125% sizing and voltage-drop calculation answer different questions.
- Use branch, feeder, and total voltage-drop budgets together.
- EVSE, lighting, heaters, and ventilation loads need sustained-current checks.
En kontinuerlig last är en last som kan gå på maximal ström i 3 timmar eller mer. Spänningsfall är spänningen som förloras i ledarimpedansen. Strömförmåga är tillåten ström utan att temperaturgränsen överskrids.
Använd först 125% enligt NEC 210.20(A), 215.3 eller 625 där det krävs. Räkna sedan med verklig kontinuerlig ström, längd, ledarmaterial och feederbudget. NEC and IEC references keep the thermal and performance checks separate.
The 125% continuous-load rule is a heat and protection rule; it does not erase the resistance of a 150-foot branch circuit.
— Hommer Zhao, Technical Director
Continuous-load design checks
En 48 A EVSE vid 240 V använder ofta en 60 A-krets. Med 6 AWG koppar och 165 ft enkel längd blir grenens fall cirka 2,6%; med 1,8% i matningen blir totalen cirka 4,4%.
| Load | Sustained current | NEC basis | Route | Design action |
|---|---|---|---|---|
| Level 2 EVSE | 32 A at 240 V | 40 A circuit | 130 ft | Compare 6 AWG Cu |
| High-output EVSE | 48 A at 240 V | 60 A circuit | 165 ft | Check feeder plus branch |
| LED lighting row | 18 A at 277 V | 125% review | 240 ft | Split row or upsize |
| Process heater | 36 A at 208 V | 45 A design current | 110 ft | Check 6 AWG and source |
| Exterior lighting | 12 A at 120 V | 15 A basis | 95 ft | Use 10 AWG or split |
For a 48-amp EV charger, document the 60-amp circuit sizing and check voltage drop at the sustained charging current.
— Hommer Zhao, Technical Director
Practical warning
125%-regeln hanterar värme och skydd, inte resistansen i en lång ledare.
Use the wire size calculator, the NEC requirements article, and the voltage drop vs ampacity guide together before material is released.
Continuous loads turn small voltage-drop misses into daily operating losses because the circuit stays loaded for hours.
— Hommer Zhao, Technical Director
FAQ
¿Calculo al 100% o al 125%?
Use la corriente sostenida real para caída de tensión y el 125% para dimensionamiento cuando NEC lo exige.
¿Un cargador EV es carga continua?
Sí. NEC 625 trata el EVSE como carga continua; 32 A suele requerir 40 A y 48 A suele requerir 60 A.
¿Qué objetivo uso en iluminación?
3% en rama y 5% total son objetivos comunes; líneas LED largas van mejor cerca de 2-3%.
¿Cuándo subo calibre?
Cuando la ruta es larga, el alimentador ya usa cerca de 2% o el equipo trabaja más de 3 horas.
¿Cómo se compara IEC?
IEC 60364-5-52 coordina corriente de diseño, método de instalación, agrupamiento, temperatura y caída permitida.
Jämför minsta ledararea med nästa storlek innan kabeln dras.
Start Calculating
Ready to apply these concepts to your project? Use our professional voltage drop calculator.
Open Calculator