Spänningsfall i LED-list: 12V/24V, NEC 411/725 och kabelarea
Beräkna LED-lister 12V och 24V med kopparresistans, NEC 411, NEC 725, IEC SELV/PELV och praktiska exempel.
LED-Streifen sind Kleinspannung, aber 12V bieten wenig Reserve. Wird das Ende dunkler oder farbstichig, prüfen Sie zuerst Leitung, Verbinder und Kupferbahn.
Kortfattat
- 12V systems have a small voltage budget; 24V reduces current for the same watts.
- Calculate each branch from watts, volts, wire size, and one-way route length.
- NEC 411 and NEC 725 guide installation; voltage drop still needs math.
- Parallel home runs or two-end feeds improve long visual runs.
Spänningsfall i LED-list: 12V/24V, NEC 411/725 och kabelarea
Ein LED-Streifen ist eine flexible Schaltung mit Leuchtdioden. Spannungsfall ist der Verlust am Leiterwiderstand. Class 2 beschreibt eine begrenzte Stromquelle.
Prüfen Sie NEC 411, NEC 725 und NEC 110.3(B); bei IEC-Projekten auch SELV/PELV und lokale Installationsregeln.
Für lange Vouten oder Schilder sind parallele Einspeisungen, beidseitige Speisung oder nähere Treiber meist besser.
Class 2 hebt den Widerstand dünner Leitungen, Clips und Dimmerklemmen nicht auf.
Vergleich 12V- und 24V-LED-Streifen
| System | Load | Example drop | Best use | Check |
|---|---|---|---|---|
| 12V single feed | 48W / 4A | 1.28V on 18 AWG, 25 ft | Short cabinets | NEC 411/725 |
| 24V single feed | 48W / 2A | 0.64V on same wire | Longer coves | Driver listing |
| Two-end feed | Current splits | Lower far-end drop | Continuous runs | Polarity and listing |
| Parallel home runs | Smaller branches | About 1% in example sign | Signs and retail | Terminal ratings |
| Daisy chain | Rising current path | Often high | Only short links | Connector amp rating |
Examples
48W bei 12V ergeben 4A. Mit 18 AWG Kupfer und 25 ft einfacher Strecke fallen etwa 1,28V bzw. 10,6% ab.
Dieselben 48W bei 24V ergeben 2A; auf derselben Leitung fallen etwa 0,64V bzw. 2,7% ab.
“For long LED runs, split current paths before blaming the driver. Four 30W branches usually beat one 120W daisy chain.”
— Hommer Zhao, Technical Director
FAQ
12V LED strip distance?
A 48W load at 12V draws 4A; on 18 AWG at 25 ft one way, drop is about 1.28V or 10.6%.
Why choose 24V?
For the same 48W, 24V uses 2A, so the same copper path drops about half the voltage percentage.
Which code sections matter?
Check NEC 411 for low-voltage lighting, NEC 725 for Class 2 circuits, and NEC 110.3(B) for listed instructions.
Can both ends be fed?
Yes when the strip manufacturer permits it and polarity is correct; it reduces current per path on long runs.
What target is reasonable?
Use 3% to 5% as a starting point, then tighten it if color or brightness uniformity is critical.
Jämför spänning, watt, kabelarea och verklig längd i kalkylatorn före montering.
Start Calculating
Ready to apply these concepts to your project? Use our professional voltage drop calculator.
Open Calculator