Sụt áp tải liên tục: 125%, cỡ dây và NEC/IEC
Chọn dây cho EVSE, chiếu sáng và gia nhiệt theo tải liên tục NEC/IEC.
Tải liên tục giữ dòng điện trong nhiều giờ. EVSE 48 A, dãy đèn 18 A hoặc bộ gia nhiệt 36 A phải được kiểm tra cả nhiệt lâu dài lẫn sụt áp thực tế.
Tóm tắt
- 3 hours or more makes the load continuous in NEC practice.
- 125% sizing and voltage-drop calculation answer different questions.
- Use branch, feeder, and total voltage-drop budgets together.
- EVSE, lighting, heaters, and ventilation loads need sustained-current checks.
Tải liên tục là tải có dòng cực đại kéo dài 3 giờ hoặc hơn. Sụt áp là điện áp mất trên trở kháng dây dẫn. Ampacity là dòng cho phép mà dây không vượt quá nhiệt độ định mức.
Trước hết áp dụng 125% theo NEC 210.20(A), 215.3 hoặc 625 khi cần; sau đó tính sụt áp bằng dòng liên tục thực, chiều dài một chiều, vật liệu dây và phần sụt áp của feeder. NEC and IEC references keep the thermal and performance checks separate.
The 125% continuous-load rule is a heat and protection rule; it does not erase the resistance of a 150-foot branch circuit.
— Hommer Zhao, Technical Director
Continuous-load design checks
EVSE 48 A ở 240 V thường dùng mạch 60 A. Với dây đồng 6 AWG dài 165 ft một chiều, nhánh sụt khoảng 2,6%; cộng feeder 1,8% thì tổng gần 4,4%.
| Load | Sustained current | NEC basis | Route | Design action |
|---|---|---|---|---|
| Level 2 EVSE | 32 A at 240 V | 40 A circuit | 130 ft | Compare 6 AWG Cu |
| High-output EVSE | 48 A at 240 V | 60 A circuit | 165 ft | Check feeder plus branch |
| LED lighting row | 18 A at 277 V | 125% review | 240 ft | Split row or upsize |
| Process heater | 36 A at 208 V | 45 A design current | 110 ft | Check 6 AWG and source |
| Exterior lighting | 12 A at 120 V | 15 A basis | 95 ft | Use 10 AWG or split |
For a 48-amp EV charger, document the 60-amp circuit sizing and check voltage drop at the sustained charging current.
— Hommer Zhao, Technical Director
Practical warning
Quy tắc 125% xử lý nhiệt và bảo vệ, không làm mất điện trở của tuyến dây dài.
Use the wire size calculator, the NEC requirements article, and the voltage drop vs ampacity guide together before material is released.
Continuous loads turn small voltage-drop misses into daily operating losses because the circuit stays loaded for hours.
— Hommer Zhao, Technical Director
FAQ
¿Calculo al 100% o al 125%?
Use la corriente sostenida real para caída de tensión y el 125% para dimensionamiento cuando NEC lo exige.
¿Un cargador EV es carga continua?
Sí. NEC 625 trata el EVSE como carga continua; 32 A suele requerir 40 A y 48 A suele requerir 60 A.
¿Qué objetivo uso en iluminación?
3% en rama y 5% total son objetivos comunes; líneas LED largas van mejor cerca de 2-3%.
¿Cuándo subo calibre?
Cuando la ruta es larga, el alimentador ya usa cerca de 2% o el equipo trabaja más de 3 horas.
¿Cómo se compara IEC?
IEC 60364-5-52 coordina corriente de diseño, método de instalación, agrupamiento, temperatura y caída permitida.
Hãy so sánh cỡ dây tối thiểu với cỡ lớn hơn trước khi kéo dây.
Start Calculating
Ready to apply these concepts to your project? Use our professional voltage drop calculator.
Open Calculator