Sụt áp dây LED: 12V/24V, NEC 411/725 và cỡ dây
Tính dây LED 12V và 24V với điện trở đồng, NEC 411, NEC 725, IEC SELV/PELV và ví dụ thực tế.
Dây LED là điện áp thấp nhưng 12V có biên rất nhỏ. Nếu cuối dây tối hoặc lệch màu, hãy kiểm tra sụt áp trên cáp, đầu nối và đồng của dây LED.
Tóm tắt
- 12V systems have a small voltage budget; 24V reduces current for the same watts.
- Calculate each branch from watts, volts, wire size, and one-way route length.
- NEC 411 and NEC 725 guide installation; voltage drop still needs math.
- Parallel home runs or two-end feeds improve long visual runs.
Sụt áp dây LED: 12V/24V, NEC 411/725 và cỡ dây
Dây LED là mạch mềm có diode phát sáng. Sụt áp là điện áp mất trên điện trở dây dẫn. Class 2 là nguồn giới hạn công suất.
Kiểm tra NEC 411, NEC 725, NEC 110.3(B); dự án IEC cần xem thêm SELV/PELV và quy định địa phương.
Với hắt trần và bảng hiệu dài, nên chia nhánh song song, cấp hai đầu hoặc đặt driver gần hơn.
Class 2 không bỏ qua điện trở của dây nhỏ, kẹp nối và dimmer.
So sánh dây LED 12V và 24V
| System | Load | Example drop | Best use | Check |
|---|---|---|---|---|
| 12V single feed | 48W / 4A | 1.28V on 18 AWG, 25 ft | Short cabinets | NEC 411/725 |
| 24V single feed | 48W / 2A | 0.64V on same wire | Longer coves | Driver listing |
| Two-end feed | Current splits | Lower far-end drop | Continuous runs | Polarity and listing |
| Parallel home runs | Smaller branches | About 1% in example sign | Signs and retail | Terminal ratings |
| Daisy chain | Rising current path | Often high | Only short links | Connector amp rating |
Examples
48W ở 12V lấy 4A. Với đồng 18 AWG và 25 ft một chiều, sụt áp khoảng 1,28V, tức 10,6%.
Cùng 48W ở 24V chỉ lấy 2A; cùng dây đó sụt khoảng 0,64V, tức 2,7%.
“For long LED runs, split current paths before blaming the driver. Four 30W branches usually beat one 120W daisy chain.”
— Hommer Zhao, Technical Director
Câu hỏi thường gặp
12V LED strip distance?
A 48W load at 12V draws 4A; on 18 AWG at 25 ft one way, drop is about 1.28V or 10.6%.
Why choose 24V?
For the same 48W, 24V uses 2A, so the same copper path drops about half the voltage percentage.
Which code sections matter?
Check NEC 411 for low-voltage lighting, NEC 725 for Class 2 circuits, and NEC 110.3(B) for listed instructions.
Can both ends be fed?
Yes when the strip manufacturer permits it and polarity is correct; it reduces current per path on long runs.
What target is reasonable?
Use 3% to 5% as a starting point, then tighten it if color or brightness uniformity is critical.
Trước khi lắp, hãy so sánh điện áp, công suất, cỡ dây và chiều dài thực trong máy tính.
Start Calculating
Ready to apply these concepts to your project? Use our professional voltage drop calculator.
Open Calculator